品牌：愛蔻

系統：燃油系統

缸內積碳清除劑

產品編號：

企業標準：Q/YKJH 4

僅供4S店使用

 產品性能： 

1、有效清洗燃燒室、活塞、活塞環槽、等部件上的積炭、附著物；

2、快速釋放卡死在活塞環槽中的活塞環,恢復活塞環的彈性及運動性；

3、 降低機油的消耗量；降低發動機的工作噪音； 降低有害氣體的排放；

4、 均衡氣缸壓力，提升動力、節省燃油。

使用方法：

1、預熱發動機并使其處在溫熱（而不是炙熱）狀態；

2、拆下火花塞（或者噴油嘴），切斷點火分電器、高壓點火圈或者電瓶之間的導線連接；

3、把缸內積碳清除劑直接倒進燃燒室內（分別對其他氣缸重復以上動作）、重新擰上火花塞，靜置10-20分鐘后，再卸下火花塞，用吸收性好的布將氣缸口遮蓋，以使噴出的臟物不至于落到漆面上，用啟動馬達啟動發動機幾秒鐘；

4、分別用破布塞緊各氣缸的火花塞孔，啟動發動馬達讓破布沖出來，裝上火花塞或者（噴油嘴）；

5、啟動發動機，以高怠速運行15分鐘，以便使剩余的已經軟化的積碳能通過排氣管排出。

備注：

1、請避免將本產品掉在汽車漆面上；

2、本產品對三元催化器、氧傳感器、橡膠制品及密封件無不良影響；

3、使用該產品后無需更換潤滑油。

Product performance:

1. Effectively clean carbon deposits and attachments on combustion chamber, piston, piston ring groove and other parts;

2. Quickly release the piston ring stuck in the piston ring groove and restore its elasticity and mobility;

3. Reduce oil consumption; Reduce the working noise of the engine; Reducing the emission of harmful gases;

4. Balance cylinder pressure, improve power and save fuel.

Usage:

1. Preheat the engine and keep it warm (not hot);

2. Remove the spark plug (or nozzle) and cut off the wire connection between the ignition distributor, high voltage ignition coil or battery;

3, pour the carbon removal agent in cylinder directly into the combustion chamber (repeat the action of other cylinder respectively), the screw on the spark plug, let stand for 10 to 20 minutes, then remove the spark plug, the cylinder mouth with good absorbent cloth cover, to make out the dirt not fall on the paint surface, start the motor start the engine for a few seconds;

4. Tighten the spark plug holes of each cylinder with the rag stopper respectively, start the motor to let the rag rush out and install the spark plug or (fuel injection nozzle);

5. Start the engine and run at a high idle speed for 15 minutes so that the remaining softened carbon deposits can be discharged through the exhaust pipe.

Remark:

1. Please avoid dropping this product on the automobile paint;

2. This product has no adverse effect on ternary catalytic converters, oxygen sensors, rubber products and sealing parts;

3. There is no need to replace lubricating oil after using this product.